Cutting Machine

The Auto elastic cutting machine is ultrasonic technical based and fully automatic machine, the cutting incision will be smooth, soft, sealed and beautiful.

Features and Function

• NTK series transducers, which is powerful and stable output.
• Double column design can offer equalizing pressure for cutting.
• 20Khz ultrasonic with little noise.
• PLC for easier and more intuitive operation.
• Free adjustable length and speed.
• With Acrylics protective cover.
• Rotary cutter rest allows 360o angle adjusting.
• Elastic material feeding device equipped to promise more accuracy cutting length.

The Nonwoven Bag Handle Cutting Machine This machine mainly is used for cutting nonwoven bag handle, which also is essential to the nonwoven bag manufacturer procedure.

Features and Function

• Simple operation, Start quickly.
• Automatic operate, without labor.
• Cutting length: 0-1.6m, adjustable and precise.
• Auto stop when material is shortage.
• Cutting mould was made of imported steel, mechanical transmission, stable and wear-resisting, longer useful life than traditional mould.
• Precisely speed regulation device, adjust cutting speed depended on customer’s requirement.

The Ultrasonic Non-woven Folding and Cutting Machine which uses of the ultrasonic sewing technology, combine with the PLC procedure controller, can finish the edges fold and cut processing with the set length and width with one machine, which can increase the productivity and improve economic performance.

The Numerical Control Cold & Hot Cutting Machine equipments adopt microcomputer control system, adjustable cold/heat cut, smooth cut section, auto feeding, auto pause, auto parameter storage, it’s very suitable for fabric cutting, film cutting, Velcro cutting, ribbon cutting, tape cutting, braid cutting, meshbelt cutting, webbing cutting, cord cutting, riband cutting, banderol cutting, nylon tape cutting, woven ribbon cutting, PP cord cutting, elastic ribbon cutting, elastic cutting, shoe lace cutting, shoestring cutting, plastic tape cutting, paper cutting, zipper cutting, woven net tube cutting, tube cutting, flat cable cutting, small cable cutting, thin electric wire cutting, metal sheet cutting, hot melt adhesive tape cutting and so on.

The Numerical Control Cold & Hot Cutting Machine: Microcomputer control cutting machine, computerized cutter, tape cutter, Velcro cutter, cord cutter, string cutter, zipper cutter, shoelace cutter, PP cord cutter, woven tape cutting, ribbon cutter, heat-shrinkable T bush cutter, hear-shrinkable tubing cutter, flat cable cutter, aluminium foil cutter, tubing cutter, PVC cutter and so on.

Features and Function

• Changeable between hot cutting and cold cutting, straight cut and bevel cut; smart design to save positioning space.
• Intelligent control, Chinese and English digital display, easy parameter setting and machine operation; free length adjust within 1-999.9 MM; accuracy identification for both light color base + deep color letters or deep color base + light color letters.
• Alternative manual operation for convenient debugging; also has auto feeding frame for labor saving.
• Accuracy cutting, high definition light sensor tracking, stable performance and also speed is fast. For example: 250 pcs 40mm cutting/min.

The semi-auto ultrasonic cutting machine is an economical and ideal manual ultrasonic cutting equipment for all kinds of ribbon cutting especially elastic band. High quality finish products, the cutting edge is soft and nice, has won a great honor from customers.

Features and Function

• Japan imported NTK transducers with strong output power and stable performance.
• The machine head is integral casting, solid, strong and prevent from backwards. more steady working performance
• Low noise with a frequency of 20KHz.
• Easy operation of the ultrasonic generator control panel
• With dividing ruler and limiting block; free length adjusting.
• Adjustable cutter rest, adjustable cutter in free directions.
• Easy cutter changing and fixing.
• High precision, smart and reasonable design, also with beautiful appearance.
• Adjustable cylinder, easy learning and operation.
• High Speed—can reach max 60 times per minute with experienced worker
• Visualized Operation—easy adjusting and auto count
• High Quality, Auto sealing, without burned, black or loose edge.
• Economical & Practical – manual cutting, can reduce the equipment cost.

The ultrasonic elastic band cutting machine is a ideal new choice for auto cutting of all kinds elastic band, with soft, smooth and artistic cutting edge, one worker can operate more than one machine at the same time which can save a lot of labor cost, thus this machine has won a great honor from the customers.

Features and Function

• Japan imported NTK transducers with strong output power and stable performance.
• The machine head is integral casting, solid, strong and prevent from backwards; more steady working performance.
• Low noise with a frequency of 20KHz.
• PLC control, easy operation.
• Free cutting length setting, auto material pick up and pulling.
• Fixed cutter rest which promises more steady performance.
• Easy cutter changing and fixing.
• High precision, smart and reasonable design, also with artistic appearance.
• Fully Auto—auto manipulator material pick up and pull, auto cutting.
• Visualized Operation—PLC touch screen, real-time displaying, auto counting.
• High Quality— Auto sealing, without burned, black or loose edge.
• Economical & Practical – auto cutting, one worker can operate more than one machine, labor saving.

35Khz Ultrasonic Fabric Cutting Machine

Features and Function

• Real time frequency automatic tracking display
• Welding modes: time, energy, and grounding.
• Amplitude division function
• Welding amplitude 10%-100% adjustable (1% accuracy)
• Amplitude compensation
• Mold impedance analysis + protection
• Overload protection
• Voltage protection (input)
• Transducer voltage protection
• 485 communication

Features and Function

• Real time frequency automatic tracking display


• Welding modes: time, energy, and grounding.


• Amplitude division function


• Welding amplitude 10%-100% adjustable (1% accuracy)


• Amplitude compensation


• Mold impedance analysis + protection


• overload protection


• Voltage protection (input)


• Transducer voltage protection


• 485 communication

The Ultrasonic Hook And Eye Tape Cutting Machine use 20KHZ ultrasonic for high frequency vibrate frication to make the cut surface get high temperature, but after cutting the temperature will back to low immediately, so ultrasonic cutting has its advantages compared to the traditional way in cutter sticking, black edge, smelly in processing, hard edge and also there won’t be loose edge or get gooseflesh.

Single chip automatic control, operators only need to feeding the material onto the feeding frame, the remaining processing will be finished by machine automatically.

The Ultrasonic Hook And Eye Tape Cutting Machine It’s a special ultrasonic cutting machine for underwear hook and eye tape cutting, it adopts cylinder and manipulator for material feeding which can effectively save the problem of cut accuracy, in the end of each tape there is a paper adhesion preventing device, tape and the paper won’t be feed at the same time (only 1mm-5mm paper be needed for each cutting.), this device will reduce the paper consumption to the lowest to promise to save the cost.

Features and Function

• This hook and eye use 20KHZ ultrasonic for high frequency vibrate frication to make the cut surface get high temperature, but after cutting the temperature will back to low immediately, so ultrasonic cutting has its advantages compared to the traditional way in cutter sticking, black edge, smelly in processing, hard edge and also there won’t be loose edge or get gooseflesh.
• Single chip automatic control, operators only need to feeding the material onto the feeding frame, the remaining processing will be finished by machine automatically.

The Label cutting machine adopt ultrasonic cutting, the incision complete beautiful, trimming neatly smooth, no rough selvedge, don`t lost edge, don`t burns, don`t yellowing, don`t black; adopt imported PLC programmable controller, color code follow the electric eye to cooperate the stepping motor automatic feed, label dimension precise cutting, computer counting, high precision, fast speed, quick and easy to adjust the length, efficient.

Features and Function

• High-precision: use inductor to locate and track to the trademark cutting location;
• Anti-static electricity: with anti-static equipment, can eliminate a lot of the static electricity generated in the cut off the mark;
• High quality: use ultrasonic cutting, the cut surface smooth, soft, don`t lost edge.

The Ultrasonic punching and cutting machine is a multi-functional machine which can cut and punch on one ribbon.

Features and Function

• Japan imported NTK transducers with strong output power and stable performance.
• Double column structure which keeps the pressure in level and fixed to promise a more steady working performance.
• Low noise with a frequency of 20KHz.
• PLC control, easy and visualized operation.
• Free adjustable length and speed from 1~9999mm;
• Rotary cutters rest; adjustable cutters in free direction.
• Easy cutting mould changing and fixing.
• High precision, smart and reasonable design, also with beautiful appearance.

The Ultrasonic Ribbon Cutting Machine Working Features: High Speed—can reach max 100 times per minutes; Visualized Operation—PLC touch screen; real- time display and auto count; High Quality- Auto sealing, without burned, black or loose edge.

Features and Function

• Japan imported NTK transducers with strong output power and stable performance.
• column structure which keeps the pressure in level and fixed to promise a more steady working performance.
• Rotary cutters rest; adjustable knives in free direction.
• Easy cutting mould changing and fixing.
• High precision, smart and reasonable design, also with beautiful appearance.
• Low noise with a frequency of 20KHz.
• PLC control, easy and visualized operation.
• Free adjustable length and speed from 1-9999mm.
• With a Acrylic protective cover, safe and better visibility.

The Ultrasonic underwear machine is successfully used ultrasound technology products in underwear.By special flowers surrounding the underwear lace edge cutting, embossing all kinds of patterns, or punching all kinds of flower holes, can sealing the edge of various irregular holes. The effect of melting soft trimming, not off the wire, no break, no damage, no flash, not to hurt the underwear material properties of the original, no skin stimulation, non-oppressive, in line with environmental protection and human health.The lace Shape can random variably,smooth and flexible lace can be accurately expressed the inner feelings and external temperament of women, Showing women’s instant eternity, Implicit humility, Inherent elegance as well as Comfortable and yet sexy, more care, Fully reflects the basic design concept of underwear and show the basic style of the products. Ultrasonic seamless underwear machine from Sheetal Enterprises fully expressed the features of seamless underwear.

Features and Function

• High speed of underwear lace cutting melting (The speed can be adjusted).
• Accurate positioning (with infrared positioning device), output can be automatically reset.
• The effect of melting soft trimming, not off the wire, no break, no damage, no flash, not to hurt the underwear material properties of the original.
• Operations continue to wave, stable operation, to save labor and high efficiency.
• Imported automatic tracking frequency ultrasonic generator.
• Original authentic Japanese import motor and silencer system.
• Flexible operation, without curvature constraints, especially for bra and underwear lace processing.

Smooth and tidy cutting edge, free of burr or fuzzy edge, optimum cutting ；Used mostly for strip cotton tapes, nylon tapes, strip ribbon, shaped into circle, swallowtail, rhombus, etc

Features and Function

• Smooth and tidy cutting edge, free of burr or fuzzy edge, optimum cutting
• PLC control automatic feeding, computer counting, high precision, high speed, simple length adjustment, high efficiency and concurrent cutting.
• Used mostly for strip cotton tapes, nylon tapes, strip ribbon, shaped into circle, swallowtail, rhombus, etc
• If the width of the tape that you want to cut is less than one inch,you can cut two pieces in one time.